Replacing the Pull Chain on a Ceiling Fan

Download Article

Download Clause

If your ceiling fan drag mountain chain is broken because information technology was pulled out of the switching, there's an easy way to fix IT. Unenclosed up the shift in the ceiling fan and remove the broken set up of chain before replacing it with a thirster one. If your switch is completely broken, purchase a replacement at a local ironware store in front removing the old one and installment the new switch. Make sure you turn the power source off before attractive apart the ceiling devotee to be safe.

1. 1

   Change by reversal the power off at the circuit breaker for safety. Locate your circuit breaker, probably either in the basement, a closet, or even outside the family. Open the breaker and turn on the power off for the room where you'll atomic number 4 working with the ceiling devotee to make a point electricity isn't still smooth when you're removing the fan's parts.^[1]

   • If you're non sure which switch is for the room with the cap fan, turn dispatch the main power just now to be innocuous.

2. 2

   Remove the light bulbs to prevent them from breaking. Set up a ladder or step pot if necessary to hand out the cap fan easily. Unscrew the light bulbs carefully and piazza them on a towel nigh. If the ceiling winnow has any sconces or globes, slay these too by unscrewing them or victimization a screwdriver to remove any screws.^[2]

   Advertizement

3. 3

   Use a screwdriver to remove the screws holding the digestible fix in place. The ceiling fan's fixture, or the briny housing where the wiring is stored, will be held together with a few perceptible screws. Utilization a screwdriver to take out these screws, loosening the fixture to see the wiring and switch.^[3]

   • Rig the screws and detachable fix piece aside in a safe place to reattach them later.

4. 4

   Unscrew the crank unofficially of the fixture that holds the flip. Front on the outside of the fixture for a puny nut. Unscrew this nut to remove it completely, letting you access the ceiling fan force chain switch. Hardened the nut aside for safekeeping.^[4]

5. 5

   Pull out the switch to inspect the chain to a greater extent closely. Now that the switch is loosened from the fixture, look at information technology up close. If the wiring of the electric switch is unsound, substitute information technology totally. Purchase the switch overt using a screwdriver to see if the chain just necessarily to be replaced with a longer piece, or if it would be unsurpassable to experience a new exchange all together.^[5]

   • If the chain looks replaceable, use a longer duration of chain you already have to fix it instead of buying another i.
   • If the switch looks broken, see a localised ironware store to buy a replacement.

   Advertisement

1. 1

   Pop open the replacement using a shrimpy screwdriver. Leverage open the tabs along the switch exploitation a screwdriver. Once you dissever it into its 2 pieces, the things inside of it, alike the chain and take shape, will be visible. With the switch candid, remove it from the wiring past pulling the wires come out of the closet from the switch.^[6]

   • Glucinium careful not to lose some of the pieces when you bolt down the switch open.
   • If you put on't see the springiness and string, give-up the ghost the evasive plate retention them inside the switch.

2. 2

   Slay the broken slice of chain from the mechanics. Remove the contents of the switch, including the broken piece of chain connected to a disc and the rebound. All of the contents inside the switch will make up loose, making it easy to simply take them unconscious. Pop the broken chain off of the disc using a screwdriver. Discard the broken chain after you've abstracted IT.^[7]

3. 3

   Put a thirster piece of chain in the rusty chain's position. Fair-minded as you removed the short broken chain, pop a longer chain that leave progress to through the mending into place in the old chain's spot. Snap the longer chain into the record where the broken mountain chain was exploitation your fingers.^[8]

4. 4

   Reassemble the switch by putt the chain and spring gage into place. Put the spring and chain attached to the disc bet on into the switch. Pull the chain through the golf hole in the switch so you bottom pull on that easily. If you popped off a protective plate that holds everything collectively, crusade this back into place too.^[9]

   • Bind refine the spring and concatenation mechanism using your feel or a screwdriver so information technology doesn't pop up while you're attaching the two main switch pieces jointly.
   • The 2 switch halves leave press cover into each other easily.

5. 5

   Place the switch back inside the fixedness and reattach the switch nut. Put the tack back in the wires just arsenic you took it extinct. Make a point you place the switch succeeding to the spot where you unscrewed the en from the outside of the fixture. Screw propeller the nut back into place to hold the switch.^[10]

   Advertisement

1. 1

   Purchase a replacement switch at your topical anesthetic home improvement store. Either take a picture of your old switch so you know which one to purchase, or disassemble the grizzly switch and take over it with you. Flavour for a "fan light exchange" or something labeled similarly.^[11]

   • Ask an employee at the home improvement OR ironmongery for avail if you're not sure which interchange to purchase.

2. 2

   Disconnect the wires attached to the old switch. Pull or twisting polish off the connectors that hold together the wires will disconnect them from the old switch. Remove each telegram that's intended to the middle-aged change over aside pull off the connectors, and drive the white-haired switch out.^[12]

   • Take a render of which wires are connected to the switch earlier disassembling it to reference the picture when putting it back together.

3. 3

   Strip 0.5–0.75 in (1.3–1.9 cm) of insulation away of the wires to attach them. Utilisation a wire stripper to strip the insulation off of the ends of the wires attached to the new switch, cutting into the insularism with the stripper before pulling information technology towards the end of the wire to slay it. This will allow the electric association to authorize through the wires.^[13]

4. 4

   Turn of events the wires together and cover them with connectors. Locate the ageing wires that your new wires testament inhere in and whirl them together tightly using a clockwise motion. Some wires are color-coded, making it easy to match the correct wires unitedly. Cover the bare wire with a twist-on connector, making sure the entire bare wire is covered.^[14]

   • Refer to the picture you took of the wires the old switch connected to, if requisite.
   • Twist-on connectors are also called cable haywire and can be found at your localized computer hardware store.

5. 5

   Put back the new switch into the fan housing to reattach the nut on the outside. Since you distant the small testis on the outside of the repair that holds the switch in place earlier, it's time to reattach it. Hold the switch inside the regular, and screw the nut back on to the alfresco of the fixture to hold the switch in situ.^[15]

   Advertisement

1. 1

   Hold the fixing complete the wiring and screw it back into put on. With your switch replaced, place the part of the mend that you removed back into lay on top of the wiring. Restrain it steady and habit the screws to bed it back in using a screwdriver.^[16]

   • Ask someone to hold the fixture in place while you screw the screws back in, if desired.

2. 2

   Put the lightbulbs back into the fixture if needed. If you separate any globes or sconces that went around the bulbs, reattach these first either by twisting them back on Beaver State using a screwdriver to reinstall the screws. Pick up the lightbulbs and carefully twist each unitary back into place in the fixture.^[17]

3. 3

   Turn the power back on through the surf. Return to the circuit breaker and flip the shift that turns back on the power. If your circuit breaker isn't labeled, make sure you reversed the just mogul back on by examination the fat-free switch in the ceiling fan room.^[18]

4. 4

   Test the pull chain to come across if it works. Flip the power change in the room if necessary to turn the lover connected. Immediately that your ceiling fan pull in range switch is fully installed, pull on it gently to see if it full treatmen. If the lights derive on Oregon the fan starts to spread ou, it's all fixed.^[19]

   • Avoid pulling along the chain using a lot of impel because this is often how it breaks.

   Ad

Add Hot Question

• Question

  If the chain honourable came inactive in my hand do I sustain to buy a new switch or can I reasonable put the chain back on?

  

  This happened to me 3 days ago. I had to purchase a fres 3-focal ratio ceiling fan replacement as the chain of mountains that stone-broke will NOT go spinal column in the switch. You'll need a big gem clip to get the wires in the terminal as per the directions that came with the one I bought from Lowe's.

• Question

  How do I jazz if the fan switch is functioning?

  

  You will need a king quizzer with a light. Check each closing for king with the switch on and off -- if it lights up when you turn the switch on, it is a close switch.

• Question

  We want to get in touch a 3-speed paries switch to replace the chain-pull turn on our cap lover. At some point on that point was a switch for a light, which was removed. There are 4 colored wires at heart the wall with wire nuts happening them. The new 3-cannonball along switch has 2 black wires. How can we tell what we are supposed to connect?

  

  2 of the wires were for the light and 2 for the lover. You will need a voltage examiner light to see which ones are power, unless 2 Beaver State 3 of the black wires are pumped-up together, and so those would be the power and the else Black wires would be for the fan or light.

• Question

  My pull range is threaded through the threaded stock that holds the light cover on, where is the switch? How do I sire to that?

  

  Start, turn off the surf or fuse for this electrical area. Remove the light cover. Look for screws that harbor the light plate in. Stay fresh one hand below the scale and hold onto it as you unscrew the screws. Hand the screws to someone, or drop into a pants' pocket. The social unit you are looking will be inside the lodging.

Ask out a Question

200 characters left

Include your email address to get a message when this interview is answered.

Submit

Advert

Things You'll Need

• Ladder
• Screwdriver

• New chain

• Wire stripper
• Replacement switch
• Twist-along connectors

Thanks for submitting a tip for review!

• Disconnect the electrical energy by turning off the power before handling the ceiling fan.

Advertisement

About This Clause

Article Summary X

To replace a ceiling fan commit trade, you'll need to take the old switching, come away the wires, and attach a new swap directly to the terminals. To start, turn hit the electrical circuit ledgeman that leads to your fan, so you don't risk electrocuting yourself. Then, remove the cover on the fan and unscrew the nut on the outside of the pull switch, so you can pull it out. Make sure you write down the colors of each telegraph and which terminals they connect to, since you'll motive this information later. Formerly you've removed the pull switch, take it to a dwelling house improvement store, and purchase a spic-and-span matchless. The new flip should live monovular in sizing, number of speeds, and wattage, or other it won't beryllium compatible. When you attach the new switch, refer to your notes so you can link the colored wires to the appropriate terminals. Once they'rhenium attached, screw the nuts backwards in, replace the winnow cover, and riffle the breaker backward along. To get wind how to attach a new switch using conducting wire nuts, read on!

Did this summary help you?

Thanks to all authors for creating a page that has been read 374,612 times.

Did this clause avail you?

Replacing the Pull Chain on a Ceiling Fan

Source: https://www.wikihow.com/Replace-a-Ceiling-Fan-Pull-Chain-Switch